Page 1 of 2

color files

Posted: Wed 08 Nov, 2017 14:12
by peotta
is not showing listed files in color in Far Manager v3.0 build 5092 x86

color files

Posted: Wed 08 Nov, 2017 14:47
by HaRT
It is an extremely bad bug report, so I doubt anyone will help you until you give enough detail.
The main questions are:
1. How to reproduce what you think is an error? (In detail.)
2. What you expect as a result of the steps.
3. What you observe instead.

color files

Posted: Wed 08 Nov, 2017 14:56
by peotta
sorry

files highlighting do not show colors

color files

Posted: Wed 08 Nov, 2017 14:57
by John Doe
F9 / Options / Panel settings / [x] Highlight files

color files

Posted: Wed 08 Nov, 2017 15:18
by DrKnS
I'll try to apply my telepathic powers...

peotta, some recent changes in Far might have caused that.
Please try to inspect your highlighting settings and make sure that all desired options (mask, attributes etc.) are activated: F9 - files highlighting and sort groups - F4 on every item.

color files

Posted: Thu 23 Nov, 2017 17:42
by vmoskalenko
Hi, have the same issue.

I just download night build 3.0.5097, update my old Far and now every file and folders has equal color (dark cyan). I.e. no difference between Folder, files, executable files, etc...
When I disable files highlighting then all files and folders becomes cyan color.
In black and white mode I had the same - only one color for all files and folders.

Could you fix it?

Thanks!

color files

Posted: Thu 23 Nov, 2017 17:46
by vmoskalenko
Few updates: The previous version was Far Manager x64 3.0.4747

color files

Posted: Thu 23 Nov, 2017 17:53
by vmoskalenko
Repro steps:
  • Full uninstall 3.0.5097 (MSI, x64)
  • Install 3.0.5000
  • Run Far. Check that file coloring is enabled. Exit far.
  • Install 3.0.5097 (MSI Upgrade)
  • Run Far. Check that file coloring is doesn't work as usual.

color files

Posted: Thu 23 Nov, 2017 21:04
by DrKnS
vmoskalenko, have you tried the steps above?

color files

Posted: Fri 24 Nov, 2017 08:27
by vmoskalenko
DrKnS wrote: Thu 23 Nov, 2017 21:04have you tried the steps above?
Yes. I did.

color files

Posted: Fri 24 Nov, 2017 12:16
by vvardja
Registered just to post in this topic.
  • F9
  • "Options"
  • "Files highlighting and sort groups"
  • Go through each entry
    • Look at the "Attributes" section. It will be disabled (no [x] in front of it).
    • If you see any options marked with [x] in the list (some entries don't), then enable the "Attributes" section.
  • Hightlighting should now be working again.
  • Save settings.
With the default highlighting settings you should go from this:

Code: Select all

| .............................. .... | *.*
| .............................. .... | *.*
| .............................. .... | *.*|..
| .............................. .... | ..
| .............................. .... | <exec>
| .............................. .... | <arc>
| .............................. .... | <temp>
| .............................. .... |
to this:

Code: Select all

| ....H+........................ .... | *.*
| ......S+...................... .... | *.*
| ..............D+.............. .... | *.*|..
| ..............D+.............. .... | ..
| .............................. .... | <exec>
| .............................. .... | <arc>
| .............................. .... | <temp>
| ..............D+.............. .... |

color files

Posted: Thu 15 Nov, 2018 17:42
by phantom4
У меня такое-же г. случилось с цветами файлов и папок после установки 5300 и 5315 в отдельные от ранее установленной версии папки. Как хорошо что я решил не ставить поверх нормальной рабочей 3535. Теперь все папки и файлы одного цвета. Никакие игры с включением выключением аттрибутов не помогли, пришлось вкучную выставлять аттрибуты для всех типов - хорошо что было куда смотреть - 3535 работает как надо. Дичь какая-то, пока 5+ придется отправить в мусорку.

color files

Posted: Fri 30 Nov, 2018 14:06
by nooker
+1
file highlightning is totally disabled after installing of 5300.
trying to find earlier build

color files

Posted: Fri 30 Nov, 2018 17:23
by nooker
phantom4 wrote: Thu 15 Nov, 2018 17:42 Никакие игры с включением выключением аттрибутов не помогли
I fixed in in a strange way:
At first I did the attributes filter as mentioned above. Nothing changed.
Then I set the "continue processing" checkbox -- everything went fine. Then I unset it back and now and seems to work as expected

color files

Posted: Fri 28 Dec, 2018 13:02
by AMG
it is fixed at nightly build (5346) (https://www.farmanager.com/nightly/Far3 ... 181228.msi)
Also I'm able to use on of previous stable build (5254) (https://www.farmanager.com/files/Far30b ... 180805.msi).
But current stable build (5300) is buggy, tested on fresh Win10.